Sound driver issue

Post here questions, problems and suggestions in English language
  • Please, check here http://websvn.kolibrios.org/listing.php ... 294df9d99e
    Also open Debug Board (there is desktop icon), close it and check /rd/1/boardlog.txt for the driver info.
    Из хаоса в космос
  • Leency wrote:Please, check here http://websvn.kolibrios.org/listing.php ... 294df9d99e
    Also open Debug Board (there is desktop icon), close it and check /rd/1/boardlog.txt for the driver info.
    I have got this boardlog text:
    Spoiler:K : HPET caps 10398201
    K : using mwait for idle loop
    K : kernel SVN r6576
    K : 2 CPU detected
    K : IDE controller programming interface 0001018A
    K : BAR0 IDE base addr 01F0
    K : BAR1 IDE base addr 03F4
    K : BAR2 IDE base addr 0170
    K : BAR3 IDE base addr 0374
    K : BAR4 IDE controller register base addr 1000
    K : IDE Interrupt FF
    K : IDE controller programming interface 0001018F
    K : BAR0 IDE base addr 1058
    K : BAR1 IDE base addr 104C
    K : BAR2 IDE base addr 1050
    K : BAR3 IDE base addr 1048
    K : BAR4 IDE controller register base addr 1020
    K : IDE Interrupt 05
    K : Channel 1 Disk 0
    K : Dev: HL-DT-ST DVDRAM GSA-T20N
    K : PIO possible modes 03
    K : PIO set mode 01
    K : Multiword DMA possible modes 07
    K : Multiword DMA set mode 00
    K : Ultra DMA possible modes 07
    K : Ultra DMA set mode 02
    K : Channel 1 Disk 1
    K : Device not found
    K : Channel 2 Disk 0
    K : Device not found
    K : Channel 2 Disk 1
    K : Device not found
    K : Channel 1 Disk 0
    K : Dev: WDC WD1600BEVS-07RST0
    K : PIO possible modes 03
    K : PIO set mode 00
    K : Multiword DMA possible modes 07
    K : Multiword DMA set mode 00
    K : Ultra DMA possible modes 7F
    K : Ultra DMA set mode 06
    K : Channel 1 Disk 1
    K : Device not found
    K : Channel 2 Disk 0
    K : Device not found
    K : Channel 2 Disk 1
    K : Device not found
    K : IDE CH1 PIO, because ATAPI drive present
    K : IDE CH2 PIO because no devices
    K : Attach Interrupt 14 Handler 8002BF74
    K : Set IDE IRQ14 return code 800604F0
    K : Attach Interrupt 15 Handler 8002BF74
    K : Set IDE IRQ15 return code 80060504
    K : IDE CH1 DMA enabled
    K : IDE CH2 PIO because no devices
    K : Attach Interrupt 5 Handler 8002BF74
    K : Set IDE IRQ5 return code 80060518
    K : driver /rd/1/drivers/vidintel.sys mapped to 8104C000
    K : driver /sys/drivers/OHCI.sys mapped to 81050000
    K : driver /sys/drivers/EHCI.sys mapped to 8104D000
    K : has_ownership
    K : HCSPARAMS=00102408, HCCPARAMS=00007070
    K : Attach Interrupt 7 Handler 8104D8E6
    K : EHCI controller at 00:1B with 8 ports initialized
    K : Attach Interrupt 11 Handler 810506C3
    K : OHCI controller at 00:18 with 4 ports initialized
    K : EHCI 810570A4: status of port 2 changed to 00001803
    K : Attach Interrupt 10 Handler 810506C3
    K : OHCI controller at 00:19 with 4 ports initialized
    K : cpu frequency 1831891000 Hz
    K : Attach Interrupt 1 Handler 80027B7C
    K : IRQ1 return code 80060568
    K : driver /rd/1/drivers/PS2MOUSE.SYS mapped to 81168000
    K : Attach Interrupt 12 Handler 81168567
    L: /SYS/SETUP Param: BOOT
    L: /SYS/LOADDRV Param: RDC
    K : driver /sys/drivers/RDC.sys mapped to 8116C000
    L: /SYS/@TASKBAR Param:
    L: /SYS/@ICON Param:
    L: /SYS/ESKIN Param:
    L: /SYS/@DOCKY Param:
    L: /SYS/NETWORK/NETCFG Param: A
    K : EHCI 810570A4 port 2 state is 00001801
    K : EHCI 810570A4: port 2 has HS or FS device, resetting
    K : EHCI 810570A4 status of port 2 is 00001005
    K : warning: async advance int missed
    K : device descriptor: 12 01 00 02 00 00 00 40 30 09 44 65 00 01 01 02 03 01
    K : found USB device with ID 0930:6544, 1 configuration(s)
    K : config descriptor: 09 02 20 00 01 01 00 80 64 09 04 00 00 02 08 06 50 00 07 05 81 02 00 02 FF 07 05 02 02 00 02 FF
    K : USB interface class/subclass/protocol = 08/06/50
    K : driver /sys/drivers/usbstor.sys mapped to 811B4000
    K : USB mass storage device detected
    K : 1 logical unit(s)
    L: /SYS/NETWORK/@ZEROCONF Param:
    K : media is ready
    K : 0 attempts, 2 ticks
    K : peripheral device type is 00
    K : direct-access mass storage device detected
    K : sector size is 512, last sector is 30297215
    Zero-config service loaded
    L: /SYS/@VOLUME Param:
    K : driver /sys/drivers/SOUND.sys mapped to 8118A000
    Detecting hardware...
    Loading INTEL_HDA
    K : driver /sys/drivers/INTEL_HDA.sys mapped to 811C0000
    HDA test version 019
    detect hardware...
    SIS 966
    PCI command 00000006
    PCI status 00000210
    lower mmio base D4200000
    upper mmio base 00000000
    GCAP = 00004400
    codec_mask = 00000003
    create primary buffer ...done
    K : Attach Interrupt 3 Handler 811C0A4C
    codec probed OK
    CAd = 0
    L: /SYS/@SS Param: ASSM
    Setup FG nodes = start_nid:total_nodes = 1:1
    L: /SYS/TMPDISK Param: A0
    FG type = 1
    Setup FG nodes = start_nid:total_nodes = 2:23
    K : driver /sys/drivers/tmpdisk.sys mapped to 811BC000
    trying to add disk

    its size is not specified, 20% from free RAM will be used

    new DiskSize: 559 MB

    operation completed successfully

    L: /SYS/SEARCHAP Param:
    Realtek ALC268
    Pin Nid = 14
    Pin Control = 00000020
    Pin Capabilities = 0001003C
    Pin def_cfg = 99138110
    Pin Amp Out caps = 80000000
    AUD_OUT found 2
    UNMUTE OUT: NID=2
    Amp val = 40:3
    CONNECT: NID=F
    IDX=0
    UNMUTE OUT: NID=14
    Enable EAPD: NID=14
    UNMUTE OUT: NID=14
    Enable EAPD: NID=14
    Pin Nid = 15
    Pin Control = 00000020
    Pin Capabilities = 0001003C
    Pin def_cfg = 0121441F
    Pin Amp Out caps = 80000000
    AUD_OUT found 3
    UNMUTE OUT: NID=3
    Amp val = 40:3
    CONNECT: NID=10
    IDX=0
    UNMUTE OUT: NID=15
    Enable EAPD: NID=15
    UNMUTE OUT: NID=15
    Enable EAPD: NID=15
    val=2
    val=3
    hda_codec_setup_stream: NID=3
    stream=1
    channel=0
    format=11
    hda_codec_setup_stream: NID=2
    stream=1
    channel=0
    format=11
    Normal mode !
    NewVolume: 0000095B
    MinVolume: 000012C0
    Searchap: additional partition is not found!
    L: AUTORUN.DAT processed
    K : destroy app object
  • Did you try to open some MP3 file via /rd/1/media/ac97snd or via /rd/1/media/pixie/pixie ?
    Из хаоса в космос
  • Yes I have tried to open mp3 files and midi files. Still no sound on my laptop.

    I forgot to say that i have a SIS968 southbridge. In the intel_hda driver source code only SIS966 is defined as a controller.
  • I'm not really good in drivers area.

    Maybe you could you try to:
    1. go to Kolibri and open /rd/1/run app
    2. run the next line: loaddrv /rd/1/sis.sys

    Another option is to add your southbridge to http://websvn.kolibrios.org/filedetails ... el_hda.asm
    Из хаоса в космос
  • It wont load the sis.sys driver because this driver is for SIS7012 audio controller with AC97 codec.

    I think that the problem is somewhere within intel_hda.sys. I will try to find the problem in the source code.
  • codec_mask = 3 is somewhat unusual - it means that there are two codecs, and I would not be surprised if the incorrect one ends up being selected. As a quick check, replace line #1315 of intel_hda.asm "mov [ctrl.codec_mask], eax" with "mov [ctrl.codec_mask], 2" and check whether it helps.
    Сделаем мир лучше!
  • I have modified and reassembled the intel_hda driver. I tried out multiple codec_mask values (from 0 to 4).
    codec_mask = 0 gives nothing
    codec_mask = 1 gives ALC268
    codec_mask = 2 gives a Motorola device, which is a modem on my laptop
    codec_mask = 3 gives ALC268
    codec_mask = 4 gives nothing

    After all this I have no sound.

    boardlog when codec_mask = 1
    Spoiler:K : HPET caps 10398201
    K : using mwait for idle loop
    K : kernel SVN r6576
    K : 2 CPU detected
    K : IDE controller programming interface 0001018A
    K : BAR0 IDE base addr 01F0
    K : BAR1 IDE base addr 03F4
    K : BAR2 IDE base addr 0170
    K : BAR3 IDE base addr 0374
    K : BAR4 IDE controller register base addr 1000
    K : IDE Interrupt FF
    K : IDE controller programming interface 0001018F
    K : BAR0 IDE base addr 1058
    K : BAR1 IDE base addr 104C
    K : BAR2 IDE base addr 1050
    K : BAR3 IDE base addr 1048
    K : BAR4 IDE controller register base addr 1020
    K : IDE Interrupt 05
    K : Channel 1 Disk 0
    K : Dev: HL-DT-ST DVDRAM GSA-T20N
    K : PIO possible modes 03
    K : PIO set mode 01
    K : Multiword DMA possible modes 07
    K : Multiword DMA set mode 00
    K : Ultra DMA possible modes 07
    K : Ultra DMA set mode 02
    K : Channel 1 Disk 1
    K : Device not found
    K : Channel 2 Disk 0
    K : Device not found
    K : Channel 2 Disk 1
    K : Device not found
    K : Channel 1 Disk 0
    K : Dev: WDC WD1600BEVS-07RST0
    K : PIO possible modes 03
    K : PIO set mode 00
    K : Multiword DMA possible modes 07
    K : Multiword DMA set mode 00
    K : Ultra DMA possible modes 7F
    K : Ultra DMA set mode 06
    K : Channel 1 Disk 1
    K : Device not found
    K : Channel 2 Disk 0
    K : Device not found
    K : Channel 2 Disk 1
    K : Device not found
    K : IDE CH1 PIO, because ATAPI drive present
    K : IDE CH2 PIO because no devices
    K : Attach Interrupt 14 Handler 8002BF74
    K : Set IDE IRQ14 return code 800604F0
    K : Attach Interrupt 15 Handler 8002BF74
    K : Set IDE IRQ15 return code 80060504
    K : IDE CH1 DMA enabled
    K : IDE CH2 PIO because no devices
    K : Attach Interrupt 5 Handler 8002BF74
    K : Set IDE IRQ5 return code 80060518
    K : driver /rd/1/drivers/vidintel.sys mapped to 8104C000
    K : driver /sys/drivers/OHCI.sys mapped to 81050000
    K : driver /sys/drivers/EHCI.sys mapped to 8104D000
    K : has_ownership
    K : HCSPARAMS=00102408, HCCPARAMS=00007070
    K : Attach Interrupt 7 Handler 8104D8E6
    K : EHCI controller at 00:1B with 8 ports initialized
    K : Attach Interrupt 11 Handler 810506C3
    K : OHCI controller at 00:18 with 4 ports initialized
    K : Attach Interrupt 10 Handler 810506C3
    K : OHCI controller at 00:19 with 4 ports initialized
    K : EHCI 810570A4: status of port 2 changed to 00001803
    K : cpu frequency 1831891000 Hz
    K : Attach Interrupt 1 Handler 80027B7C
    K : IRQ1 return code 80060568
    K : driver /rd/1/drivers/PS2MOUSE.SYS mapped to 81168000
    K : Attach Interrupt 12 Handler 81168567
    L: /SYS/SETUP Param: BOOT
    L: /SYS/LOADDRV Param: RDC
    K : driver /sys/drivers/RDC.sys mapped to 8116C000
    L: /SYS/@TASKBAR Param:
    L: /SYS/@ICON Param:
    L: /SYS/ESKIN Param:
    L: /SYS/@DOCKY Param:
    L: /SYS/NETWORK/NETCFG Param: A
    K : EHCI 810570A4 port 2 state is 00001801
    K : EHCI 810570A4: port 2 has HS or FS device, resetting
    K : EHCI 810570A4 status of port 2 is 00001005
    K : warning: async advance int missed
    K : device descriptor: 12 01 00 02 00 00 00 40 30 09 44 65 00 01 01 02 03 01
    K : found USB device with ID 0930:6544, 1 configuration(s)
    K : config descriptor: 09 02 20 00 01 01 00 80 64 09 04 00 00 02 08 06 50 00 07 05 81 02 00 02 FF 07 05 02 02 00 02 FF
    K : USB interface class/subclass/protocol = 08/06/50
    K : driver /sys/drivers/usbstor.sys mapped to 811B4000
    K : USB mass storage device detected
    K : 1 logical unit(s)
    L: /SYS/NETWORK/@ZEROCONF Param:
    K : media is ready
    K : 0 attempts, 2 ticks
    K : peripheral device type is 00
    K : direct-access mass storage device detected
    K : sector size is 512, last sector is 30297215
    Zero-config service loaded
    L: /SYS/@VOLUME Param:
    K : driver /sys/drivers/SOUND.sys mapped to 8118A000
    Detecting hardware...
    Loading INTEL_HDA
    K : driver /sys/drivers/INTEL_HDA.sys mapped to 811BE000
    HDA test version 019
    detect hardware...
    SIS 966
    PCI command 00000006
    PCI status 00000210
    lower mmio base D4200000
    upper mmio base 00000000
    GCAP = 00004400
    codec_mask = 00000003
    create primary buffer ...done
    K : Attach Interrupt 3 Handler 811BEA4C
    codec probed OK
    CAd = 0
    L: /SYS/@SS Param: ASSM
    Setup FG nodes = start_nid:total_nodes = 1:1
    FG type = 1
    L: /SYS/TMPDISK Param: A0
    Setup FG nodes = start_nid:total_nodes = 2:23
    K : driver /sys/drivers/tmpdisk.sys mapped to 811BA000
    trying to add disk

    its size is not specified, 20% from free RAM will be used

    new DiskSize: 559 MB

    operation completed successfully

    L: /SYS/SEARCHAP Param:
    Realtek ALC268
    Pin Nid = 14
    Pin Control = 00000020
    Pin Capabilities = 0001003C
    Pin def_cfg = 99138110
    Pin Amp Out caps = 80000000
    AUD_OUT found 2
    UNMUTE OUT: NID=2
    Amp val = 40:3
    CONNECT: NID=F
    IDX=0
    UNMUTE OUT: NID=14
    Enable EAPD: NID=14
    UNMUTE OUT: NID=14
    Enable EAPD: NID=14
    Pin Nid = 15
    Pin Control = 00000020
    Pin Capabilities = 0001003C
    Pin def_cfg = 0121441F
    Pin Amp Out caps = 80000000
    AUD_OUT found 3
    UNMUTE OUT: NID=3
    Amp val = 40:3
    CONNECT: NID=10
    IDX=0
    UNMUTE OUT: NID=15
    Enable EAPD: NID=15
    UNMUTE OUT: NID=15
    Enable EAPD: NID=15
    val=2
    val=3
    hda_codec_setup_stream: NID=3
    stream=1
    channel=0
    format=11
    hda_codec_setup_stream: NID=2
    stream=1
    channel=0
    format=11
    Normal mode !
    NewVolume: 000001DF
    MinVolume: 000012C0
    Searchap: additional partition is not found!
    L: AUTORUN.DAT processed
    TRK Notes: max=76 min=60
    K : destroy app object
    K : destroy app object
    boardlog when codec_mask = 2
    Spoiler:K : HPET caps 10398201
    K : using mwait for idle loop
    K : kernel SVN r6576
    K : 2 CPU detected
    K : IDE controller programming interface 0001018A
    K : BAR0 IDE base addr 01F0
    K : BAR1 IDE base addr 03F4
    K : BAR2 IDE base addr 0170
    K : BAR3 IDE base addr 0374
    K : BAR4 IDE controller register base addr 1000
    K : IDE Interrupt FF
    K : IDE controller programming interface 0001018F
    K : BAR0 IDE base addr 1058
    K : BAR1 IDE base addr 104C
    K : BAR2 IDE base addr 1050
    K : BAR3 IDE base addr 1048
    K : BAR4 IDE controller register base addr 1020
    K : IDE Interrupt 05
    K : Channel 1 Disk 0
    K : Dev: HL-DT-ST DVDRAM GSA-T20N
    K : PIO possible modes 03
    K : PIO set mode 01
    K : Multiword DMA possible modes 07
    K : Multiword DMA set mode 00
    K : Ultra DMA possible modes 07
    K : Ultra DMA set mode 02
    K : Channel 1 Disk 1
    K : Device not found
    K : Channel 2 Disk 0
    K : Device not found
    K : Channel 2 Disk 1
    K : Device not found
    K : Channel 1 Disk 0
    K : Dev: WDC WD1600BEVS-07RST0
    K : PIO possible modes 03
    K : PIO set mode 00
    K : Multiword DMA possible modes 07
    K : Multiword DMA set mode 00
    K : Ultra DMA possible modes 7F
    K : Ultra DMA set mode 06
    K : Channel 1 Disk 1
    K : Device not found
    K : Channel 2 Disk 0
    K : Device not found
    K : Channel 2 Disk 1
    K : Device not found
    K : IDE CH1 PIO, because ATAPI drive present
    K : IDE CH2 PIO because no devices
    K : Attach Interrupt 14 Handler 8002BF74
    K : Set IDE IRQ14 return code 800604F0
    K : Attach Interrupt 15 Handler 8002BF74
    K : Set IDE IRQ15 return code 80060504
    K : IDE CH1 DMA enabled
    K : IDE CH2 PIO because no devices
    K : Attach Interrupt 5 Handler 8002BF74
    K : Set IDE IRQ5 return code 80060518
    K : driver /rd/1/drivers/vidintel.sys mapped to 8104C000
    K : driver /sys/drivers/OHCI.sys mapped to 81050000
    K : driver /sys/drivers/EHCI.sys mapped to 8104D000
    K : has_ownership
    K : HCSPARAMS=00102408, HCCPARAMS=00007070
    K : Attach Interrupt 7 Handler 8104D8E6
    K : EHCI controller at 00:1B with 8 ports initialized
    K : Attach Interrupt 11 Handler 810506C3
    K : OHCI controller at 00:18 with 4 ports initialized
    K : Attach Interrupt 10 Handler 810506C3
    K : OHCI controller at 00:19 with 4 ports initialized
    K : cpu frequency 1831891000 Hz
    K : Attach Interrupt 1 Handler 80027B7C
    K : IRQ1 return code 80060568
    K : driver /rd/1/drivers/PS2MOUSE.SYS mapped to 81168000
    K : Attach Interrupt 12 Handler 81168567
    K : EHCI 810570A4: status of port 1 changed to 00001803
    L: /SYS/SETUP Param: BOOT
    L: /SYS/LOADDRV Param: RDC
    K : driver /sys/drivers/RDC.sys mapped to 8116C000
    L: /SYS/@TASKBAR Param:
    L: /SYS/@ICON Param:
    L: /SYS/ESKIN Param:
    L: /SYS/@DOCKY Param:
    L: /SYS/NETWORK/NETCFG Param: A
    K : EHCI 810570A4 port 1 state is 00001801
    K : EHCI 810570A4: port 1 has HS or FS device, resetting
    K : EHCI 810570A4 status of port 1 is 00001005
    K : warning: async advance int missed
    K : device descriptor: 12 01 00 02 00 00 00 40 30 09 44 65 00 01 01 02 03 01
    K : found USB device with ID 0930:6544, 1 configuration(s)
    K : config descriptor: 09 02 20 00 01 01 00 80 64 09 04 00 00 02 08 06 50 00 07 05 81 02 00 02 FF 07 05 02 02 00 02 FF
    K : USB interface class/subclass/protocol = 08/06/50
    K : driver /sys/drivers/usbstor.sys mapped to 811B1000
    K : USB mass storage device detected
    K : 1 logical unit(s)
    L: /SYS/NETWORK/@ZEROCONF Param:
    K : media is ready
    K : 0 attempts, 2 ticks
    K : peripheral device type is 00
    K : direct-access mass storage device detected
    K : sector size is 512, last sector is 30297215
    Zero-config service loaded
    L: /SYS/@VOLUME Param:
    K : driver /sys/drivers/SOUND.sys mapped to 81194000
    Detecting hardware...
    Loading INTEL_HDA
    K : driver /sys/drivers/INTEL_HDA.sys mapped to 811BE000
    HDA test version 019
    detect hardware...
    SIS 966
    PCI command 00000006
    PCI status 00000210
    lower mmio base D4200000
    upper mmio base 00000000
    GCAP = 00004400
    codec_mask = 00000003
    create primary buffer ...done
    K : Attach Interrupt 3 Handler 811BEA4C
    codec probed OK
    CAd = 1
    L: /SYS/@SS Param: ASSM
    Setup FG nodes = start_nid:total_nodes = 1:1
    FG type = 2
    no AFG node found, trying another codec
    L: /SYS/TMPDISK Param: A0
    Setup FG nodes = start_nid:total_nodes = 2:24
    K : driver /sys/drivers/tmpdisk.sys mapped to 811BB000
    trying to add disk

    its size is not specified, 20% from free RAM will be used

    new DiskSize: 559 MB

    operation completed successfully

    L: /SYS/SEARCHAP Param:
    Motorola unknown codec id 00003055
    val=0
    device not found
    K : destroy app object
    Searchap: additional partition is not found!
    L: AUTORUN.DAT processed
  • For the beginning get full debug information by setting

    Code: Select all

    FDEBUG          equ 1
    in the file intel_hda.asm
  • I have set FDEBUG to 1 and assembled the intel_hda.asm file. I got the following boardlog:
    Spoiler:K : HPET caps 10398201
    K : using mwait for idle loop
    K : kernel SVN r6576
    K : 2 CPU detected
    K : IDE controller programming interface 0001018A
    K : BAR0 IDE base addr 01F0
    K : BAR1 IDE base addr 03F4
    K : BAR2 IDE base addr 0170
    K : BAR3 IDE base addr 0374
    K : BAR4 IDE controller register base addr 1000
    K : IDE Interrupt FF
    K : IDE controller programming interface 0001018F
    K : BAR0 IDE base addr 1058
    K : BAR1 IDE base addr 104C
    K : BAR2 IDE base addr 1050
    K : BAR3 IDE base addr 1048
    K : BAR4 IDE controller register base addr 1020
    K : IDE Interrupt 05
    K : Channel 1 Disk 0
    K : Dev: HL-DT-ST DVDRAM GSA-T20N
    K : PIO possible modes 03
    K : PIO set mode 01
    K : Multiword DMA possible modes 07
    K : Multiword DMA set mode 00
    K : Ultra DMA possible modes 07
    K : Ultra DMA set mode 02
    K : Channel 1 Disk 1
    K : Device not found
    K : Channel 2 Disk 0
    K : Device not found
    K : Channel 2 Disk 1
    K : Device not found
    K : Channel 1 Disk 0
    K : Dev: WDC WD1600BEVS-07RST0
    K : PIO possible modes 03
    K : PIO set mode 00
    K : Multiword DMA possible modes 07
    K : Multiword DMA set mode 00
    K : Ultra DMA possible modes 7F
    K : Ultra DMA set mode 06
    K : Channel 1 Disk 1
    K : Device not found
    K : Channel 2 Disk 0
    K : Device not found
    K : Channel 2 Disk 1
    K : Device not found
    K : IDE CH1 PIO, because ATAPI drive present
    K : IDE CH2 PIO because no devices
    K : Attach Interrupt 14 Handler 8002BF74
    K : Set IDE IRQ14 return code 800604F0
    K : Attach Interrupt 15 Handler 8002BF74
    K : Set IDE IRQ15 return code 80060504
    K : IDE CH1 DMA enabled
    K : IDE CH2 PIO because no devices
    K : Attach Interrupt 5 Handler 8002BF74
    K : Set IDE IRQ5 return code 80060518
    K : driver /rd/1/drivers/vidintel.sys mapped to 8104C000
    K : driver /sys/drivers/OHCI.sys mapped to 81050000
    K : driver /sys/drivers/EHCI.sys mapped to 8104D000
    K : has_ownership
    K : HCSPARAMS=00102408, HCCPARAMS=00007070
    K : Attach Interrupt 7 Handler 8104D8E6
    K : EHCI controller at 00:1B with 8 ports initialized
    K : Attach Interrupt 11 Handler 810506C3
    K : OHCI controller at 00:18 with 4 ports initialized
    K : Attach Interrupt 10 Handler 810506C3
    K : OHCI controller at 00:19 with 4 ports initialized
    K : EHCI 810570A4: status of port 1 changed to 00001803
    K : cpu frequency 1831891000 Hz
    K : Attach Interrupt 1 Handler 80027B7C
    K : IRQ1 return code 80060568
    K : driver /rd/1/drivers/PS2MOUSE.SYS mapped to 81168000
    K : Attach Interrupt 12 Handler 81168567
    L: /SYS/SETUP Param: BOOT
    L: /SYS/LOADDRV Param: RDC
    K : driver /sys/drivers/RDC.sys mapped to 81174000
    L: /SYS/@TASKBAR Param:
    L: /SYS/@ICON Param:
    L: /SYS/ESKIN Param:
    L: /SYS/@DOCKY Param:
    L: /SYS/NETWORK/NETCFG Param: A
    K : EHCI 810570A4 port 1 state is 00001801
    K : EHCI 810570A4: port 1 has HS or FS device, resetting
    K : EHCI 810570A4 status of port 1 is 00001005
    K : warning: async advance int missed
    K : device descriptor: 12 01 00 02 00 00 00 40 30 09 44 65 00 01 01 02 03 01
    K : found USB device with ID 0930:6544, 1 configuration(s)
    K : config descriptor: 09 02 20 00 01 01 00 80 64 09 04 00 00 02 08 06 50 00 07 05 81 02 00 02 FF 07 05 02 02 00 02 FF
    K : USB interface class/subclass/protocol = 08/06/50
    K : driver /sys/drivers/usbstor.sys mapped to 81194000
    K : USB mass storage device detected
    K : 1 logical unit(s)
    L: /SYS/NETWORK/@ZEROCONF Param:
    Zero-config service loaded
    L: /SYS/@VOLUME Param:
    K : driver /sys/drivers/SOUND.sys mapped to 81192000
    Detecting hardware...
    Loading INTEL_HDA
    K : driver /sys/drivers/INTEL_HDA.sys mapped to 811CA000
    HDA test version 019
    detect hardware...
    SIS 966
    PCI command 00000006
    PCI status 00000210
    lower mmio base D4200000
    upper mmio base 00000000
    GCAP = 00004400
    codec_mask = 00000003
    create primary buffer ...done
    K : Attach Interrupt 3 Handler 811CAA70
    K : media is ready
    K : 0 attempts, 2 ticks
    K : peripheral device type is 00
    K : direct-access mass storage device detected
    K : sector size is 512, last sector is 30297215
    codec probed OK
    CAd = 0
    Q: 000F0000
    A: 10EC0268
    Q: 000F0001
    L: /SYS/@SS Param: ASSM
    Q: 000F0002
    A: 00100003
    Q: 000F0004
    A: 00010001
    Setup FG nodes = start_nid:total_nodes = 1:1
    Q: 001F0005
    L: /SYS/TMPDISK Param: A0
    A: 00000101
    FG type = 1
    Q: 001F0004
    A: 00020023
    Setup FG nodes = start_nid:total_nodes = 2:23
    Widget capabilities:
    Q: 002F0009
    A: 0000001D
    Q: 003F0009
    K : driver /sys/drivers/tmpdisk.sys mapped to 811BB000
    trying to add disk

    its size is not specified, 20% from free RAM will be used

    new DiskSize: 559 MB

    A: 0000001D
    Q: 004F0009
    A: 00F00000
    Q: 005F0009
    A: 00F00000
    Q: 006F0009
    A: 00000211
    Q: 007F0009
    A: 00100111
    Q: 008F0009
    A: 00100111
    Q: 009F0009
    A: 00F00000
    Q: 00AF0009
    A: 00F00000
    Q: 00BF0009
    operation completed successfully

    A: 00F00000
    Q: 00CF0009
    L: /SYS/SEARCHAP Param:
    A: 00F00000
    Q: 00DF0009
    A: 00F00000
    Q: 00EF0009
    A: 0020010A
    Q: 00FF0009
    A: 0020010B
    Q: 010F0009
    A: 0020010B
    Q: 011F0009
    A: 00F00000
    Q: 012F0009
    A: 00400001
    Q: 013F0009
    A: 00400001
    Q: 014F0009
    A: 0040018D
    Q: 015F0009
    A: 0040018D
    Q: 016F0009
    A: 0040010C
    Q: 017F0009
    A: 00F00000
    Q: 018F0009
    A: 0040018F
    Q: 019F0009
    A: 0040008B
    Q: 01AF0009
    A: 0040018F
    Q: 01BF0009
    A: 00F00000
    Q: 01CF0009
    A: 00400001
    Q: 01DF0009
    A: 00400000
    Q: 01EF0009
    A: 00400380
    Q: 01FF0009
    A: 00F00000
    Q: 020F0009
    A: 00F00040
    Q: 021F0009
    A: 00F00000
    Q: 022F0009
    A: 00F00000
    Q: 023F0009
    A: 0030010D
    Q: 024F0009
    A: 0030010D
    Pin configurations:
    Q: 012F1C00
    A: 411111F0
    Q: 013F1C00
    A: 411111F0
    Q: 014F1C00
    A: 99138110
    Q: 015F1C00
    A: 0121441F
    Q: 016F1C00
    A: 411111F0
    Q: 018F1C00
    A: 01A19C2E
    Q: 019F1C00
    A: 99A38920
    Q: 01AF1C00
    A: 411111F0
    Q: 01CF1C00
    A: 411111F0
    Q: 01DF1C00
    A: 40138205
    Q: 01EF1C00
    A: 411111F0
    Q: 001F2000
    A: 17341110
    Q: 00170500
    Q: 001F0500
    Realtek ALC268
    Q: 001F0012
    Q: 001F000D
    Q: 001F0004
    A: 00020023
    Q: 002F0012
    A: 00034040
    Q: 003F0012
    A: 00034040
    Q: 007F000E
    A: 00000001
    Q: 007F0200
    A: 00000024
    Q: 008F000E
    A: 00000001
    Q: 008F0200
    A: 00000023
    Q: 00EF000E
    A: 00000001
    Q: 00EF0200
    A: 00000002
    Q: 00EF000D
    A: 80000000
    Q: 00FF000E
    A: 00000002
    Q: 00FF0200
    A: 00001D02
    Q: 00FF000D
    A: 80000000
    Q: 010F000E
    A: 00000003
    Q: 010F0200
    A: 00021D03
    Q: 010F000D
    A: 80000000
    Q: 012F000C
    A: 00000020
    Q: 012F0700
    Q: 013F000C
    A: 00000020
    Q: 013F0700
    Q: 014F000E
    A: 00000001
    Q: 014F0200
    A: 0000000F
    Q: 014F000C
    A: 0001003C
    Q: 014F0700
    A: 00000020
    Q: 014F0012
    A: 80000000
    Q: 015F000E
    A: 00000001
    Q: 015F0200
    A: 00000010
    Q: 015F000C
    A: 0001003C
    Q: 015F0700
    A: 00000020
    Q: 015F0012
    A: 80000000
    Q: 016F000E
    A: 00000001
    Q: 016F0200
    A: 0000000E
    Q: 016F000C
    A: 00000010
    Q: 016F0700
    Q: 016F0012
    A: 80000000
    Q: 018F000E
    A: 00000001
    Q: 018F0200
    A: 00000002
    Q: 018F000C
    A: 00003734
    Q: 018F0700
    A: 00000021
    Q: 018F0012
    A: 80000000
    Q: 018F000D
    A: 004F0200
    Q: 019F000C
    A: 00003724
    Q: 019F0700
    A: 00000020
    Q: 019F000D
    A: 004F0200
    Q: 01AF000E
    A: 00000001
    Q: 01AF0200
    A: 00000002
    Q: 01AF000C
    A: 00003734
    Q: 01AF0700
    A: 00000020
    Q: 01AF0012
    A: 80000000
    Q: 01AF000D
    A: 004F0200
    Q: 01CF000C
    A: 00000020
    Q: 01CF0700
    A: 00000020
    Q: 01DF000C
    A: 00000020
    Q: 01DF0700
    A: 00000020
    Q: 01EF000E
    A: 00000001
    Q: 01EF0200
    A: 00000006
    Q: 01EF000C
    A: 00000010
    Q: 01EF0700
    A: 00000040
    Q: 023F000E
    A: 00000007
    Q: 023F0200
    A: 1C1A1918
    Q: 023F0204
    A: 00121514
    Q: 023F0012
    A: 80051F0B
    Q: 024F000E
    A: 00000007
    Q: 024F0200
    A: 1C1A1918
    Q: 024F0204
    A: 00131514
    Q: 024F0012
    A: 80051F0B
    Sequence of codec nodes:
    NID: 0x2
    NID: 0x3
    NID: 0x4
    NID: 0x5
    NID: 0x6
    NID: 0x7
    NID: 0x8
    NID: 0x9
    NID: 0xA
    NID: 0xB
    NID: 0xC
    NID: 0xD
    NID: 0xE
    NID: 0xF
    NID: 0x10
    NID: 0x11
    NID: 0x17
    NID: 0x1B
    NID: 0x1F
    NID: 0x20
    NID: 0x21
    NID: 0x22
    NID: 0x23
    NID: 0x24
    NID: 0x1D
    NID: 0x14
    NID: 0x15
    NID: 0x19
    NID: 0x18
    NID: 0x12
    NID: 0x13
    NID: 0x16
    NID: 0x1A
    NID: 0x1C
    NID: 0x1E
    Q: 014F000C
    A: 0001003C
    Q: 01470894
    Pin Nid = 14
    Pin Control = 00000020
    Pin Capabilities = 0001003C
    Pin def_cfg = 99138110
    Pin Amp Out caps = 80000000
    AUD_OUT found 2
    UNMUTE OUT: NID=2
    Q: 0023A040
    Q: 00239040
    Amp val = 40:3
    CONNECT: NID=F
    IDX=0
    Q: 00F70100
    UNMUTE OUT: NID=14
    Q: 01470C02
    Enable EAPD: NID=14
    Q: 0143A000
    Q: 01439000
    UNMUTE OUT: NID=14
    Q: 01470C02
    Enable EAPD: NID=14
    Q: 0143A000
    Q: 01439000
    Q: 014707C0
    Q: 015F000C
    A: 0001003C
    Q: 01570895
    Pin Nid = 15
    Pin Control = 00000020
    Pin Capabilities = 0001003C
    Pin def_cfg = 0121441F
    Pin Amp Out caps = 80000000
    AUD_OUT found 3
    UNMUTE OUT: NID=3
    Q: 0033A040
    Q: 00339040
    Amp val = 40:3
    CONNECT: NID=10
    IDX=0
    Q: 01070100
    UNMUTE OUT: NID=15
    Q: 01570C02
    Enable EAPD: NID=15
    Q: 0153A000
    Q: 01539000
    UNMUTE OUT: NID=15
    Q: 01570C02
    Enable EAPD: NID=15
    Q: 0153A000
    Q: 01539000
    Q: 015707C0
    val=2
    val=3
    hda_codec_setup_stream: NID=3
    stream=1
    channel=0
    format=11
    Q: 00370610
    Q: 00320011
    hda_codec_setup_stream: NID=2
    stream=1
    channel=0
    format=11
    Q: 00270610
    Q: 00220011
    Normal mode !
    NewVolume: 000001DF
    MinVolume: 000012C0
    Q: 0033A039
    Q: 00339039
    Searchap: additional partition is not found!
    L: AUTORUN.DAT processed
    minimp3 -- a small MPEG-1 Audio Layer III player based on ffmpeg

    /usbhd0/1/002.MP3
    Bytes:5782091
    Now Playing: /usbhd0/1/002.MP3
    samples:44100
    channel:2K : driver /sys/drivers/INFINITY.sys mapped to A4404000
    start play
    K : destroy app object
  • Just to be sure..
    Did you also check the headphone jack or just built-in speakers?
    "Any intelligent fool can make things bigger, more complex, and more violent. It takes a touch of genius -- and a lot of courage -- to move in the opposite direction." Albert Einstein
  • Ok, thanks. I'll get some time to analyze the log.
  • hidnplayr wrote:Just to be sure..
    Did you also check the headphone jack or just built-in speakers?
    Yes I checked the headphone jack. The boardlog shows unsolicited events, but there is no sound.
  • Try attached driver. It is a bit newer version than in distro, also it should support headphones.
    Attachments
    intel_hda.sys (6.95 KiB)
    Downloaded 275 times
    Из хаоса в космос
  • Who is online

    Users browsing this forum: No registered users and 7 guests