Новые драйвера для ATI Radeon.

Drivers for various video cards
  • paladinrus
    Posts 24
    Joined: Sat Jul 14, 2007 12:17 pm

    Пардон, невнимательно читал :).

    Вот

    Code: Select all

    Unknown card detected: 00007280:0000174B:00000000.
Detected an ATI Radeon X1950 on an unidentified card
Memory base_0 E0000000 size 10000000
Memory base_1 00000000 size 00000100
Memory base_2 F1000000 size 00010000
Memory base_3 00000000 size 00000001
Memory base_4 00000000 size 00000001
Memory base_5 00000000 size 00000001
Io base_0 00000000 size 10000000
Io base_1 00009000 size 00000100
Io base_2 00000000 size 00010000
Io base_3 00000000 size 00000001
Io base_4 00000000 size 00000001
Io base_5 00000000 size 00000001
Mapped IO at 80DC9000 (size 00010000)
The detected amount of videoram exceeds the PCI BAR aperture.
Using only 262144kB of the total 524288kB.
VideoRAM: 262144 kByte
Getting BIOS copy from legacy VBIOS location
ATOM BIOS Rom: 
 SubsystemVendorID: 0x0000174B SubsystemID: 0x0000E190
 IOBaseAddress: 0x00009000
 Filename: SA999E25.003
 BIOS Bootup Message: 
        113-A99931-00 RV570 BIOS 702m/581e                                          
        
Call to AtomBIOS Init succeeded
Detected VGA mode.
    .
    Aka Rus.
  • Wildwest
    Posts 1001
    Joined: Wed May 18, 2005 7:27 pm

    Второй тест

    Code: Select all

    Unknown card detected: 00007187:0000174B:00000000.
Detected an ATI Radeon X1300/X1550 on an unidentified card
Memory base_0 D0000000 size 10000000
Memory base_1 00000000 size 00000100
Memory base_2 E5000000 size 00010000
Memory base_3 00000000 size 00000001
Memory base_4 00000000 size 00000001
Memory base_5 00000000 size 00000001
Io base_0 00000000 size 10000000
Io base_1 0000C000 size 00000100
Io base_2 00000000 size 00010000
Io base_3 00000000 size 00000001
Io base_4 00000000 size 00000001
Io base_5 00000000 size 00000001
Mapped IO at 80EE4000 (size 00010000)
VideoRAM: 262144 kByte
Getting BIOS copy from legacy VBIOS location
ATOM BIOS Rom:
 SubsystemVendorID: 0x0000174B SubsystemID: 0x00003000
 IOBaseAddress: 0x0000C000
 Filename: JC8513SA.002
 BIOS Bootup Message:
	X1550 Rialto 256mb DDR2 BIOS 550e/400m Channel AB

Call to AtomBIOS Init succeeded
Detected VGA mode.
  • User avatar
    <Lrz> Kernel Optimizer
    Posts 657
    Joined: Mon Jan 16, 2006 7:58 pm

    Code: Select all

    Unknown card detected: 000071C6:0000174B:00000000.
Detected an ATI Radeon X1650 on an unidentified card
Memory base_0 D0000000 size 10000000
Memory base_1 00000000 size 00000100
Memory base_2 E1000000 size 00010000
Memory base_3 00000000 size 00000001
Memory base_4 00000000 size 00000001
Memory base_5 00000000 size 00000001
Io base_0 00000000 size 10000000
Io base_1 0000C000 size 00000100
Io base_2 00000000 size 00010000
Io base_3 00000000 size 00000001
Io base_4 00000000 size 00000001
Io base_5 00000000 size 00000001
Mapped IO at 80DB4000 (size 00010000)
VideoRAM: 262144 kByte
Getting BIOS copy from legacy VBIOS location
ATOM BIOS Rom: 
 SubsystemVendorID: 0x0000174B SubsystemID: 0x0000E040
 IOBaseAddress: 0x0000C000
 Filename: 8E0402SA.003
 BIOS Bootup Message: 
        RV530XT AGP Rialto BIOS DDR2 550e/650m                                      
Call to AtomBIOS Init succeeded
Detected VGA mode.
  • Serge Kernel Developer
    Posts 3952
    Joined: Wed Mar 08, 2006 6:25 pm

    Спасибо всем за тесты.
    Вот ещё один ftp://kolibrios.org/upload/rhd_03.7z
    Большая часть для карт с ATOMBIOS. На других картах
    просто повторение предыдущих.

    Информация о разъёмах и подключённых устройствах
    Framebuffer space used by Firmware (kb): 20
    Start of VRAM area used by Firmware: 0x01000000
    AtomBIOS requests 20kB of VRAM scratch space
    AtomBIOS VRAM scratch base: 0x01000000
    rhdAtomAllocateFbScratch: FW FB scratch area not located at the end of VRAM. Scratch End: 0x01005000 VRAM End: 0x10000000
    Cannot get VRAM scratch space. Allocating in main memory instead
    Call to AtomBIOS Set FB Space succeeded
    Default Engine Clock: 500000
    Default Memory Clock: 405000
    Maximum Pixel ClockPLL Frequency Output: 1100000
    Minimum Pixel ClockPLL Frequency Output: 0
    Maximum Pixel ClockPLL Frequency Input: 13500
    Minimum Pixel ClockPLL Frequency Input: 1000
    Maximum Pixel Clock: 400000
    Reference Clock: 27000
    Default Engine Clock: 500000
    I2C clock prescale value: 00007F27
    I2C bus "RHD I2C line 0" initialized.
    I2C clock prescale value: 00007F27
    I2C bus "RHD I2C line 1" initialized.
    I2C clock prescale value: 00007F27
    I2C bus "RHD I2C line 2" initialized.
    Detected VGA mode.
    AtomBIOS Connector[0]: VGA Device: CRT1 Output: 1 HW DDC 0 NO HPD
    AtomBIOS Connector[2]: SVIDEO Device: TV1 Output: 2 NO DDC NO HPD
    AtomBIOS Connector[3]: DVI-I Device: DFP1 Output: 3 HW DDC 1 HPD 0
    AtomBIOS Connector[4]: DVI-I Device: CRT2 Output: 2 HW DDC 1 NO HPD
    Connector[0] {RHD_CONNECTOR_VGA, " CRT1", RHD_DDC_0, RHD_HPD_NONE, { RHD_OUTPUT_DACA, RHD_OUTPUT_NONE } }
    Connector[1] {RHD_CONNECTOR_TV, " TV1", DDC_NONE, RHD_HPD_NONE, { RHD_OUTPUT_DACB, RHD_OUTPUT_NONE } }
    Connector[2] {RHD_CONNECTOR_DVI, " DFP1 CRT2", RHD_DDC_1, RHD_HPD_0, { RHD_OUTPUT_TMDSA, RHD_OUTPUT_DACB } }
    Call to AtomBIOS Get Connectors succeeded
    RHDConnectorsInit: 0 ( CRT1) type 1, ddc 0, hpd 0
    Attaching Output DAC A to Connector VGA 1
    RHDConnectorsInit: 1 ( TV1) type 4, ddc 255, hpd 0
    Attaching Output DAC B to Connector TV
    RHDConnectorsInit: 2 ( DFP1 CRT2) type 2, ddc 1, hpd 1
    Attaching Output TMDS A to Connector DVI-I 1
    Attaching Output DAC B to Connector DVI-I 1
  • paladinrus
    Posts 24
    Joined: Sat Jul 14, 2007 12:17 pm

    Вот третий тест

    Code: Select all

    Detected an ATI Radeon X1950 on a Sapphire X1950 Pro
Memory base_0 0xE0000000 size 0x10000000
Memory base_2 0xF1000000 size 0x00010000
Io base_1 0x00009000 size 0x00000100
Mapped IO at 80DB3000 (size 00010000)
The detected amount of videoram exceeds the PCI BAR aperture.
Using only 262144kB of the total 524288kB.
VideoRAM: 262144 kByte
Getting BIOS copy from legacy VBIOS location
ATOM BIOS Rom: 
 SubsystemVendorID: 0x0000174B SubsystemID: 0x0000E190
 IOBaseAddress: 0x00009000
 Filename: SA999E25.003
 BIOS Bootup Message: 
        113-A99931-00 RV570 BIOS 702m/581e                                          
        
Call to AtomBIOS Init succeeded
Framebuffer space used by Firmware (kb): 20
Start of VRAM area used by Firmware: 0x1FFFB000
AtomBIOS requests 20kB of VRAM scratch space
AtomBIOS VRAM scratch base: 0x1FFFB000
rhdAtomAllocateFbScratch: FW FB scratch area 1FFFB000 (size: 00005000) extends beyond available framebuffer size 10000000
Cannot get VRAM scratch space. Allocating in main memory instead
Call to AtomBIOS Set FB Space succeeded
Default Engine Clock: 581000
Default Memory Clock: 702000
Maximum Pixel ClockPLL Frequency Output: 1100000
Minimum Pixel ClockPLL Frequency Output: 0
Maximum Pixel ClockPLL Frequency Input: 13500
Minimum Pixel ClockPLL Frequency Input: 1000
Maximum Pixel Clock: 400000
Reference Clock: 27000
Default Engine Clock: 581000
I2C clock prescale value: 00007F2D
I2C bus "RHD I2C line 0" initialized.
I2C clock prescale value: 00007F2D
I2C bus "RHD I2C line 1" initialized.
I2C clock prescale value: 00007F2D
I2C bus "RHD I2C line 2" initialized.
Detected VGA mode.
AtomBIOS Connector[0]: DVI-I Device: CRT1 Output: 1 HW DDC 0 NO HPD
AtomBIOS Connector[2]: SVIDEO Device: TV1 Output: 2 NO DDC NO HPD
AtomBIOS Connector[3]: DVI-I Device: DFP1 Output: 3 HW DDC 1 HPD 0
AtomBIOS Connector[4]: DVI-I Device: CRT2 Output: 2 HW DDC 1 NO HPD
AtomBIOS Connector[9]: DVI-I Device: DFP3 Output: 4 HW DDC 0 HPD 1
Connector[0] {RHD_CONNECTOR_DVI, " CRT1 DFP3", RHD_DDC_0, RHD_HPD_1, { RHD_OUTPUT_DACA, RHD_OUTPUT_LVTMA } }
Connector[1] {RHD_CONNECTOR_TV, " TV1", DDC_NONE, RHD_HPD_NONE, { RHD_OUTPUT_DACB, RHD_OUTPUT_NONE } }
Connector[2] {RHD_CONNECTOR_DVI, " DFP1 CRT2", RHD_DDC_1, RHD_HPD_0, { RHD_OUTPUT_TMDSA, RHD_OUTPUT_DACB } }
Call to AtomBIOS Get Connectors succeeded
RHDConnectorsInit: 0 ( CRT1 DFP3) type 2, ddc 0, hpd 2
Attaching Output DAC A to Connector DVI-I 1
Attaching Output TMDS B to Connector DVI-I 1
RHDConnectorsInit: 1 ( TV1) type 4, ddc 255, hpd 0
Attaching Output DAC B to Connector TV
RHDConnectorsInit: 2 ( DFP1 CRT2) type 2, ddc 1, hpd 1
Attaching Output TMDS A to Connector DVI-I 2
Attaching Output DAC B to Connector DVI-I 2
    .
    Aka Rus.
  • User avatar
    <Lrz> Kernel Optimizer
    Posts 657
    Joined: Mon Jan 16, 2006 7:58 pm

    Unknown card detected: 000071C6:0000174B:0000E040.
    Detected an ATI Radeon X1650 on an unidentified card
    Memory base_0 0xD0000000 size 0x10000000
    Memory base_2 0xE1000000 size 0x00010000
    Io base_1 0x0000C000 size 0x00000100
    Mapped IO at 80D9E000 (size 00010000)
    VideoRAM: 262144 kByte
    Getting BIOS copy from legacy VBIOS location
    ATOM BIOS Rom:
    SubsystemVendorID: 0x0000174B SubsystemID: 0x0000E040
    IOBaseAddress: 0x0000C000
    Filename: 8E0402SA.003
    BIOS Bootup Message:
    RV530XT AGP Rialto BIOS DDR2 550e/650m

    Call to AtomBIOS Init succeeded
    Framebuffer space used by Firmware (kb): 20
    Start of VRAM area used by Firmware: 0x0FFFB000
    AtomBIOS requests 20kB of VRAM scratch space
    AtomBIOS VRAM scratch base: 0x0FFFB000
    Call to AtomBIOS Set FB Space succeeded
    Default Engine Clock: 600000
    Default Memory Clock: 700000
    Maximum Pixel ClockPLL Frequency Output: 1100000
    Minimum Pixel ClockPLL Frequency Output: 0
    Maximum Pixel ClockPLL Frequency Input: 13500
    Minimum Pixel ClockPLL Frequency Input: 1000
    Maximum Pixel Clock: 400000
    Reference Clock: 27000
    Default Engine Clock: 600000
    I2C clock prescale value: 00007F2F
    I2C bus "RHD I2C line 0" initialized.
    I2C clock prescale value: 00007F2F
    I2C bus "RHD I2C line 1" initialized.
    I2C clock prescale value: 00007F2F
    I2C bus "RHD I2C line 2" initialized.
    Detected VGA mode.
    AtomBIOS Connector[0]: VGA Device: CRT1 Output: 1 HW DDC 0 NO HPD
    AtomBIOS Connector[2]: SVIDEO Device: TV1 Output: 2 NO DDC NO HPD
    AtomBIOS Connector[3]: DVI-I Device: DFP1 Output: 3 HW DDC 1 HPD 0
    AtomBIOS Connector[4]: DVI-I Device: CRT2 Output: 2 HW DDC 1 NO HPD
    Connector[0] {RHD_CONNECTOR_VGA, " CRT1", RHD_DDC_0, RHD_HPD_NONE, { RHD_OUTPUT_DACA, RHD_OUTPUT_NONE } }
    Connector[1] {RHD_CONNECTOR_TV, " TV1", DDC_NONE, RHD_HPD_NONE, { RHD_OUTPUT_DACB, RHD_OUTPUT_NONE } }
    Connector[2] {RHD_CONNECTOR_DVI, " DFP1 CRT2", RHD_DDC_1, RHD_HPD_0, { RHD_OUTPUT_TMDSA, RHD_OUTPUT_DACB } }
    Call to AtomBIOS Get Connectors succeeded
    RHDConnectorsInit: 0 ( CRT1) type 1, ddc 0, hpd 0
    Attaching Output DAC A to Connector VGA 1
    RHDConnectorsInit: 1 ( TV1) type 4, ddc 255, hpd 0
    Attaching Output DAC B to Connector TV
    RHDConnectorsInit: 2 ( DFP1 CRT2) type 2, ddc 1, hpd 1
    Attaching Output TMDS A to Connector DVI-I 1
    Attaching Output DAC B to Connector DVI-I 1
  • Serge Kernel Developer
    Posts 3952
    Joined: Wed Mar 08, 2006 6:25 pm

    Новый супертест для карт с ATOMBIOS.
    ftp://kolibrios.org/upload/rhd_04.7z

    Определение монитора и доступных режимов.
    начало теста повторяется поэтом интересен последний фрагмент
    EDID data for SyncMaster
    Manufacturer: SAM Model: 2a1 Serial#: 1346777401
    Year: 2007 Week: 24
    EDID Version: 1.3
    Digital Display Input
    Max H-Image Size [cm]: horiz.: 38 vert.: 30
    Gamma: 2.20
    DPMS capabilities: Off; RGB/Color Display
    First detailed timing is preferred mode
    redX: 0.640 redY: 0.329 greenX: 0.300 greenY: 0.600
    blueX: 0.150 blueY: 0.060 whiteX: 0.313 whiteY: 0.329
    Supported VESA Video Modes:
    720x400@70Hz
    640x480@60Hz
    640x480@67Hz
    640x480@72Hz
    640x480@75Hz
    800x600@56Hz
    800x600@60Hz
    800x600@72Hz
    800x600@75Hz
    832x624@75Hz
    1024x768@60Hz
    1024x768@70Hz
    1024x768@75Hz
    1280x1024@75Hz
    1152x870@75Hz
    Manufacturer's mask: 0
    Supported Future Video Modes:
    #0: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
    #1: hsize: 1280 vsize 960 refresh: 60 vid: 16513
    #2: hsize: 1152 vsize 864 refresh: 75 vid: 20337
    Supported additional Video Mode:
    clock: 108.0 MHz Image Size: 376 x 301 mm
    h_active: 1280 h_sync: 1328 h_sync_end 1440 h_blank_end 1688 h_border: 0
    v_active: 1024 v_sync: 1025 v_sync_end 1028 v_blanking: 1066 v_border: 0
    Ranges: V min: 56 V max: 75 Hz, H min: 30 H max: 81 kHz, PixClock max 140 MHz
    Monitor name: SyncMaster
    Serial No: HMBP600201
    Connector "DVI-I 1" uses Monitor "SyncMaster":
    Bandwidth: 140MHz
    Horizontal timing:
    30.0 - 81.0kHz
    Vertical timing:
    56.0 - 75.0Hz
    DPI: 86x87
    Allows reduced blanking.
    Attached modes:
    Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync
    Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync
    Modeline "640x480" 31.00 640 656 720 840 480 481 484 500 -hsync -vsync
    Modeline "640x480" 31.00 640 664 704 832 480 489 491 520 -hsync -vsync
    Modeline "640x480" 30.00 640 704 768 864 480 483 486 525 -hsync -vsync
    Modeline "640x480" 25.00 640 656 752 800 480 490 492 525 -hsync -vsync
    Modeline "720x400" 28.00 720 738 846 900 400 412 414 449 -hsync +vsync
    Modeline "1280x1024" 135.00 1280 1296 1440 1688 1024 1025 1028 1066 +hsync +vsync
    Modeline "1024x768" 78.00 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
    Modeline "1024x768" 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
    Modeline "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
    Modeline "832x624" 57.00 832 864 928 1152 624 625 628 667 -hsync -vsync
    Modeline "800x600" 49.00 800 816 896 1056 600 601 604 625 +hsync +vsync
    Modeline "800x600" 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync
    Modeline "1152x864" 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync
    Modeline "1280x1024" 109.00 1280 1361 1496 1712 1024 1027 1034 1063 -hsync +vsync
    Modeline "1280x960" 101.00 1280 1358 1493 1706 960 963 967 996 -hsync +vsync
    Modeline "1152x864" 104.00 1152 1227 1349 1546 864 867 871 905 -hsync +vsync
    Listing modesetting layout:

    CRTC 1: tied to PLL 1 and LUT A:
    Outputs: TMDS A (DVI-I 1)

    CRTC 2: unused

    Unused Outputs: DAC A, DAC B
  • Wildwest
    Posts 1001
    Joined: Wed May 18, 2005 7:27 pm

    Провести 3-й и 4-й тесты не удается. На доске отладки пишет
    Unresolved PciRead16
    Unresolved PciRead8
    Unresolved PciWrite16
    Unresolved PciWrite8
  • Serge Kernel Developer
    Posts 3952
    Joined: Wed Mar 08, 2006 6:25 pm

    Wildwest
    Надо обновить ядро до #747+. Можно скачать с rhd_02
  • Wildwest
    Posts 1001
    Joined: Wed May 18, 2005 7:27 pm

    Code: Select all

    Detected an ATI Radeon X1300/X1550 on a RV516 : Radeon X1300/X1550
Memory base_0 0xd0000000 size 0x10000000
Memory base_2 0xe5000000 size 0x10000
Io base_1 0xc000 size 0x100
Mapped IO at 80e9b000 (size 10000)
VideoRAM: 262144 kByte
Getting BIOS copy from legacy VBIOS location
ATOM BIOS Rom:
	SubsystemVendorID: 0x174b SubsystemID: 0x3000
	IOBaseAddress: 0xc000
	Filename: JC8513SA.002
	BIOS Bootup Message:
X1550 Rialto 256mb DDR2 BIOS 550e/400m Channel AB

Call to AtomBIOS Init succeeded
Framebuffer space used by Firmware (kb): 20
Start of VRAM area used by Firmware: 0x7ffb000
AtomBIOS requests 20kB of VRAM scratch space
AtomBIOS VRAM scratch base: 0x7ffb000
rhdAtomAllocateFbScratch: FW FB scratch area not located at the end of VRAM. Scratch End: 0x8000000 VRAM End: 0x10000000
Cannot get VRAM scratch space. Allocating in main memory instead
Call to AtomBIOS Set FB Space succeeded
Default Engine Clock: 550000
Default Memory Clock: 400000
Maximum Pixel ClockPLL Frequency Output: 1100000
Minimum Pixel ClockPLL Frequency Output: 0
Maximum Pixel ClockPLL Frequency Input: 13500
Minimum Pixel ClockPLL Frequency Input: 1000
Maximum Pixel Clock: 400000
Reference Clock: 27000
Default Engine Clock: 550000
I2C clock prescale value: 0X7F2B
I2C bus "RHD I2C line 0" initialized.
I2C clock prescale value: 0X7F2B
I2C bus "RHD I2C line 1" initialized.
I2C clock prescale value: 0X7F2B
I2C bus "RHD I2C line 2" initialized.
Detected VGA mode.
Minimum Pixel ClockPLL Frequency Output: 0
Maximum Pixel ClockPLL Frequency Output: 1100000
Maximum Pixel Clock: 400000
Reference Clock: 27000
AtomBIOS Connector[0]: VGA Device: CRT1 Output: 1 HW DDC 0 NO HPD
AtomBIOS Connector[2]: SVIDEO Device: TV1 Output: 2 NO DDC NO HPD
AtomBIOS Connector[4]: DVI-I Device: CRT2 Output: 2 HW DDC 1 NO HPD
AtomBIOS Connector[9]: DVI-I Device: DFP3 Output: 4 HW DDC 1 HPD 1
Connector[0] {RHD_CONNECTOR_VGA, " CRT1", RHD_DDC_0, RHD_HPD_NONE, { RHD_OUTPUT_DACA, RHD_OUTPUT_NONE } }
Connector[1] {RHD_CONNECTOR_TV, " TV1", DDC_NONE, RHD_HPD_NONE, { RHD_OUTPUT_DACB, RHD_OUTPUT_NONE } }
Connector[2] {RHD_CONNECTOR_DVI, " CRT2 DFP3", RHD_DDC_1, RHD_HPD_0 /*swapped*/, { RHD_OUTPUT_DACB, RHD_OUTPUT_LVTMA } }
Call to AtomBIOS Get Connectors succeeded
RHDConnectorsInit: 0 ( CRT1) type 1, ddc 0, hpd 0
Attaching Output DAC A to Connector VGA 1
RHDConnectorsInit: 1 ( TV1) type 4, ddc 255, hpd 0
Attaching Output DAC B to Connector TV
RHDConnectorsInit: 2 ( CRT2 DFP3) type 2, ddc 1, hpd 2
Attaching Output DAC B to Connector DVI-I 1
Attaching Output TMDS B to Connector DVI-I 1
DACASense: DAC: 0x07
DACBSenseCRT: connector type 4 is not supported.
I2C device "RHD I2C line 0:ddc2" registered at address 0xa0.
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4993
Sections to follow: 0
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4996
DDC checksum not correct
Checksum error in EDID block
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4996
DDC checksum not correct
Checksum error in EDID block
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4996
DDC checksum not correct
Checksum error in EDID block
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4988
SW_STATUS: 0x1 4998
SW_STATUS: 0x1 4996
DDC checksum not correct
Checksum error in EDID block
I2C device "RHD I2C line 0:ddc2" removed.
EDIDModeFromDetailedTiming: Ignoring: We only handle separate sync.
EDID data for AL1923
Manufacturer: ACR  Model: 783  Serial#: 4418
Year: 2006  Week: 35
EDID Version: 1.3
Analog Display Input,  Input Voltage Level: 0.700/0.700 V
Sync:  Separate
Max H-Image Size [cm]: horiz.: 37  vert.: 30
Gamma: 2.20
DPMS capabilities: Suspend Off; RGB/Color Display
First detailed timing is preferred mode
redX: 0.651 redY: 0.320   greenX: 0.300 greenY: 0.600
blueX: 0.153 blueY: 0.109   whiteX: 0.313 whiteY: 0.329
Supported VESA Video Modes:
720x400@70Hz
640x480@60Hz
640x480@67Hz
640x480@72Hz
640x480@75Hz
800x600@56Hz
800x600@60Hz
800x600@72Hz
800x600@75Hz
832x624@75Hz
1024x768@60Hz
1024x768@70Hz
1024x768@75Hz
1280x1024@75Hz
1152x870@75Hz
Manufacturer's mask: 0
Supported Future Video Modes:
#0: hsize: 1152  vsize 864  refresh: 75  vid: 20337
#1: hsize: 1280  vsize 720  refresh: 60  vid: 49281
#2: hsize: 1280  vsize 960  refresh: 60  vid: 16513
#3: hsize: 1280  vsize 1024  refresh: 60  vid: 32897
Supported additional Video Mode:
clock: 108.0 MHz   Image Size:	5 x 4 mm
h_active: 1280	h_sync: 1328  h_sync_end 1440 h_blank_end 1688 h_border: 0
v_active: 1024	v_sync: 1025  v_sync_end 1028 v_blanking: 1066 v_border: 0
Ranges: V min: 55  V max: 75 Hz, H min: 30  H max: 81 kHz, PixClock max 140 MHz
Monitor name: AL1923
 ACER-V1.00
Connector "VGA 1" uses Monitor "AL1923":
    Bandwidth: 140MHz
    Horizontal timing:
	30.0 - 81.0kHz
    Vertical timing:
	55.0 - 75.0Hz
    DPI: 88x87
    Attached modes:
	Modeline "800x600"  40.00  800 840 968 1056  600 601 605 628 +hsync +vsync
	Modeline "800x600"  36.00  800 824 896 1024  600 601 603 625 +hsync +vsync
	Modeline "640x480"  31.00  640 656 720 840  480 481 484 500 -hsync -vsync
	Modeline "640x480"  31.00  640 664 704 832  480 489 491 520 -hsync -vsync
	Modeline "640x480"  30.00  640 704 768 864  480 483 486 525 -hsync -vsync
	Modeline "640x480"  25.00  640 656 752 800  480 490 492 525 -hsync -vsync
	Modeline "720x400"  28.00  720 738 846 900  400 412 414 449 -hsync +vsync
	Modeline "1280x1024" 135.00  1280 1296 1440 1688  1024 1025 1028 1066 +hsync +vsync
	Modeline "1024x768"  78.00  1024 1040 1136 1312  768 769 772 800 +hsync +vsync
	Modeline "1024x768"  75.00  1024 1048 1184 1328  768 771 777 806 -hsync -vsync
	Modeline "1024x768"  65.00  1024 1048 1184 1344  768 771 777 806 -hsync -vsync
	Modeline "832x624"  57.00  832 864 928 1152  624 625 628 667 -hsync -vsync
	Modeline "800x600"  49.00  800 816 896 1056  600 601 604 625 +hsync +vsync
	Modeline "800x600"  50.00  800 856 976 1040  600 637 643 666 +hsync +vsync
	Modeline "1152x864" 108.00  1152 1216 1344 1600  864 865 868 900 +hsync +vsync
	Modeline "1152x864" 104.00  1152 1227 1349 1546  864 867 871 905 -hsync +vsync
	Modeline "1280x720"  74.00  1280 1342 1474 1668  720 723 728 748 -hsync +vsync
	Modeline "1280x960" 101.00  1280 1358 1493 1706  960 963 967 996 -hsync +vsync
	Modeline "1280x1024" 109.00  1280 1361 1496 1712  1024 1027 1034 1063 -hsync +vsync
Listing modesetting layout:

	CRTC 1: tied to PLL 1 and LUT A:
		Outputs: DAC A (VGA 1)

	CRTC 2: unused

		Unused Outputs: DAC B, TMDS B
  • Serge Kernel Developer
    Posts 3952
    Joined: Wed Mar 08, 2006 6:25 pm

    Wildwest
    clock: 108.0 MHz Image Size: 5 x 4 mm
    Так всё время определяется?

    P.S.
    Хорошая новость. Смена видеорежима успешно работает.
  • paladinrus
    Posts 24
    Joined: Sat Jul 14, 2007 12:17 pm

    Четвёртый тест.
    Attachments
    ATI.TXT (7.45 KiB)
    Downloaded 251 times
    Aka Rus.
  • Wildwest
    Posts 1001
    Joined: Wed May 18, 2005 7:27 pm

    всё время
  • User avatar
    Ghost Kernel Developer
    Posts 558
    Joined: Mon Mar 20, 2006 10:44 am

    Serge
    Смена режима через V86 или средствами драйвера?
    • Post Reply

    Return to “Video”

    Who is online

    Users browsing this forum: No registered users and 2 guests