K : HPET caps 8086A201 K : using mwait for idle loop K : kernel SVN r5998 K : 2 CPU detected K : IDE controller programming interface 00010180 K : BAR0 IDE base addr 01F0 K : BAR1 IDE base addr 03F4 K : BAR2 IDE base addr 0170 K : BAR3 IDE base addr 0374 K : BAR4 IDE controller register base addr 1800 K : IDE Interrupt FF K : Channel 1 Disk 0 K : Dev: Hitachi HTS543212L9SA02 K : PIO possible modes 03 K : PIO set mode 01 K : Multiword DMA possible modes 07 K : Multiword DMA set mode 00 K : Ultra DMA possible modes 7F K : Ultra DMA set mode 05 K : Channel 1 Disk 1 K : Device not found K : Channel 2 Disk 0 K : Device not found K : Channel 2 Disk 1 K : Device not found K : IDE CH1 DMA enabled K : IDE CH2 PIO because no devices K : Attach Interrupt 14 Handler 8003866C K : Set IDE IRQ14 return code 80062770 K : Attach Interrupt 15 Handler 8003866C K : Set IDE IRQ15 return code 80062784 K : clear_pci_ide_interrupts: port[1802] = 20 -> 20; port[180A] = 00 -> 00 K : driver /rd/1/drivers/vidintel.sys mapped to 80DF7000 Intel videocard detected, PciId=8086:8108, which is unknown K : driver /sys/drivers/UHCI.sys mapped to 80DFB000 K : driver /sys/drivers/EHCI.sys mapped to 80DF8000 K : has_ownership K : HCSPARAMS=00103208, HCCPARAMS=00006871 K : Attach Interrupt 11 Handler 80DF88E6 K : EHCI controller at 00:EF with 8 ports initialized K : EHCI 80E020A4: status of port 0 changed to 00001803 K : EHCI 80E020A4: status of port 2 changed to 00001803 K : EHCI 80E020A4: status of port 3 changed to 00001803 K : EHCI 80E020A4: status of port 5 changed to 00001403 K : EHCI 80E020A4: status of port 7 changed to 00001803 K : UHCI 00:E8 with 2 ports: PCI=00000005K : Attach Interrupt 10 Handler 80DFB721 K : UHCI 80E05830 connect status changed, 0082/0080 K : UHCI 00:E9 with 2 ports: PCI=00000005K : Attach Interrupt 5 Handler 80DFB721 K : UHCI 80E07830 connect status changed, 0082/0080 K : UHCI 80E07830 connect status changed, 009A/0090 K : UHCI 00:EA with 2 ports: PCI=00000005K : Attach Interrupt 3 Handler 80DFB721 K : UHCI 80E09830 connect status changed, 00A2/00A0 K : cpu frequency 1596018000 Hz K : Attach Interrupt 1 Handler 80039748 K : IRQ1 return code 800627E8 K : driver /rd/1/drivers/PS2MOUSE.SYS mapped to 80F15000 L: /SYS/SETUP Param: BOOT L: /SYS/LOADDRV Param: RDC K : driver /sys/drivers/RDC.sys mapped to 80F2E000 L: /SYS/NETWORK/NETCFG Param: A K : driver /sys/drivers/RTL8169.sys mapped to 80F32000 RTL8169: Loading driver RTL8169: Hooking into device, dev:0, bus:2, irq:F, addr:00002000 L: /SYS/NETWORK/@ZEROCONF Param: Zero-config service loaded L: /SYS/ESKIN Param: K : EHCI 80E020A4 port 0 state is 00001801 K : EHCI 80E020A4: port 0 has HS or FS device, resetting K : EHCI 80E020A4 port 2 state is 00001801 K : EHCI 80E020A4 port 3 state is 00001801 K : EHCI 80E020A4 port 5 state is 00001401 K : EHCI 80E020A4: port 5 has LS device, releasing K : EHCI 80E020A4 port 7 state is 00001801 K : EHCI 80E020A4: status of port 5 changed to 00003002 K : EHCI 80E020A4 status of port 0 is 00001005 K : EHCI 80E020A4: port 2 has HS or FS device, resetting K : device descriptor: 12 01 00 02 00 00 00 40 E4 08 4E 01 00 00 01 02 03 01 K : found USB device with ID 08E4:014E, 1 configuration(s) K : config descriptor: 09 02 20 00 01 01 00 C0 32 09 04 00 00 02 08 06 50 00 07 05 01 02 00 02 00 07 05 82 02 00 02 00 K : EHCI 80E020A4 status of port 2 is 00001005 K : EHCI 80E020A4: port 3 has HS or FS device, resetting K : USB interface class/subclass/protocol = 08/06/50 K : driver /sys/drivers/usbstor.sys mapped to 80F54000 K : USB mass storage device detected K : 1 logical unit(s) K : device descriptor: 12 01 00 02 00 00 00 40 DA 0B 79 81 00 00 01 02 03 01 K : found USB device with ID 0BDA:8179, 1 configuration(s) K : media is ready K : 0 attempts, 3 ticks K : EHCI 80E020A4 status of port 3 is 00001801 K : releasing to companion K : EHCI 80E020A4: port 7 has HS or FS device, resetting K : EHCI 80E020A4: status of port 3 changed to 00003002 K : config descriptor: 09 02 27 00 01 01 00 A0 FA 09 04 00 00 03 FF FF FF 00 07 05 81 02 00 02 00 07 05 02 02 00 02 00 07 05 03 02 00 02 00 K : peripheral device type is 05 K : USB interface class/subclass/protocol = FF/FF/FF K : failed to load class driver K : EHCI 80E020A4 status of port 7 is 00001005 K : device descriptor: 12 01 00 02 00 00 00 40 64 85 00 10 00 0A 01 02 03 01 K : found USB device with ID 8564:1000, 1 configuration(s) K : config descriptor: 09 02 20 00 01 01 00 80 FA 09 04 00 00 02 08 06 50 00 07 05 02 02 00 02 00 07 05 81 02 00 02 00 K : USB interface class/subclass/protocol = 08/06/50 K : USB mass storage device detected K : 1 logical unit(s) K : media is ready K : 0 attempts, 0 ticks K : peripheral device type is 00 K : direct-access mass storage device detected K : sector size is 512, last sector is 61767679 L: /SYS/@VOLUME Param: K : driver /sys/drivers/SOUND.sys mapped to 8105B000 Detecting hardware... Loading INTEL_HDA K : driver /sys/drivers/INTEL_HDA.sys mapped to 81062000 HDA test version 019 detect hardware... Intel Poulsbo PCI command 00000006 PCI status 00000010 lower mmio base B0050004 upper mmio base 00000000 GCAP = 00002200 HDA snoop disabled, enabling ... OK codec_mask = 00000001 create primary buffer ...done K : Attach Interrupt 255 Handler 81062A34 L: /SYS/@TASKBAR Param: L: /SYS/@DOCKY Param: L: /SYS/@ICON Param: L: /SYS/@SS Param: ASSM L: /SYS/TMPDISK Param: A0 K : driver /sys/drivers/tmpdisk.sys mapped to 810A0000 пробую добавить виртуальный диск его размер не указан, 10% свободной ОЗУ будет использовано размер диска будет: 100 MB операция успешно завершена L: /SYS/SEARCHAP Param: K : UHCI 80E07830 connect status changed, 0093/0091 K : port is shared with EHCI, skipping initial debounce K : UHCI 80E09830 connect status changed, 01A3/01A1 K : port is shared with EHCI, skipping initial debounce K : UHCI 80E07830 status 0280/0093 K : reset done K : UHCI 80E09830 status 0280/01A3 K : reset done K : UHCI 80E07830 status 0095 K : UHCI 80E09830 status 01A5 K : disabling pipe with first TD: K : 00A28034 188007FF 00E0002D 0068E89C K : 00000000 00000000 00000000 874FE044 K : disabling pipe with first TD: K : 00A280C4 1C8007FF 00E0002D 0069089C K : 00000000 00000000 00000000 874FE0D4 K : Timeout in USB device initialization, trying to reset... K : Timeout in USB device initialization, trying to reset... K : UHCI 80E07830 status 0288/0093 K : reset done K : UHCI 80E09830 status 0288/01A3 K : reset done K : UHCI 80E07830 status 0095 K : UHCI 80E09830 status 01A5 get_response timeout: polling the codec once codec probed OK CAd = 0 Searchap: additional partition is not found! L: /SYS/DEVELOP/BOARD Param: /usbhd0/1/boardlog.txt L: AUTORUN.DAT processed K : disabling pipe with first TD: K : 00A280C4 188007FF 00E0002D 0068E89C K : 00000000 00000000 00000000 874FE0D4 K : disabling pipe with first TD: K : 00A28034 1C8007FF 00E0002D 0069089C K : 00000000 00000000 00000000 874FE044 K : Timeout in USB device initialization, trying to reset... K : Timeout in USB device initialization, trying to reset... K : UHCI 80E07830 status 0288/0093 K : reset done K : UHCI 80E09830 status 0288/01A3 K : reset done K : UHCI 80E07830 status 0095 K : UHCI 80E09830 status 01A5 get_response timeout: polling the codec once K : disabling pipe with first TD: K : 00A28034 188007FF 00E0002D 0068E89C K : 00000000 00000000 00000000 874FE044 K : disabling pipe with first TD: K : 00A280C4 1C8007FF 00E0002D 0069089C K : 00000000 00000000 00000000 874FE0D4 K : Timeout in USB device initialization, trying to reset... K : Timeout in USB device initialization, trying to reset... K : UHCI 80E07830 status 0288/0093 K : reset done K : UHCI 80E09830 status 0288/01A3 K : reset done K : UHCI 80E07830 status 0095 K : UHCI 80E09830 status 01A5 get_response timeout: switching to polling mode Setup FG nodes = start_nid:total_nodes = 1:1 FG type = 1 Setup FG nodes = start_nid:total_nodes = 2:1A Realtek unknown codec id 00000260 Pin Nid = 10 Pin Control = 00000020 Pin Capabilities = 0001003F Pin def_cfg = 01214110 Pin Amp Out caps = 80000000 AUD_OUT found 2 CONNECT: NID=9 IDX=0 UNMUTE OUT: NID=9 Amp val = 40:3 UNMUTE OUT: NID=10 Enable EAPD: NID=10 UNMUTE OUT: NID=10 Enable EAPD: NID=10 val=2 val=0 hda_codec_setup_stream: NID=2 stream=1 channel=0 format=11 Normal mode ! NewVolume: 0000095B MinVolume: 000012C0 RTL8169: Detected chip: unknown RTL8169 clone K : Attach Interrupt 255 Handler 80F32CDC RTL8169: Could not attach int handler! RTL8169: Link is up, phystatus=0xFF RTL8169: init OK! Trying to contact DHCP server No answer from DHCP server No answer from DHCP server K : disabling pipe with first TD: K : 00A280C4 188007FF 00E0002D 0068E89C K : 00000000 00000000 00000000 874FE0D4 K : disabling pipe with first TD: K : 00A28034 1C8007FF 00E0002D 0069089C K : 00000000 00000000 00000000 874FE044 K : error 17 in SET_ADDRESS, USB device disabled K : error 17 in SET_ADDRESS, USB device disabled No answer from DHCP server Link Local IP assigned: 169.254.179.192